Receive a 5% DISCOUNT when purchasing online until the end of February 2021. Use this code at checkout: NC0221 Shop Now

Shop here online for your fluid power components
Over 50,000 products available from stock
Consistently high quality

Diffusers Type SRV

Diffusers for installation in hydraulic tanks for direct connection to the return line using female thread BSP or NPT. Calms the return-flow oil and reduces foaming and tank noise using two concentric steel tubes with offset discharge openings. Installation completely below the minimum liquid level with the closed surface facing towards the pump intake side. Upper end cap made of aluminium, other components made of steel, galvanised.

Filters / Sorting

Categories

10 Results
Diffuser Thread: 3/4" BSP
  • STAUFF Material Description SRV-050-G12
  • STAUFF Material No. 1910000420
  • STAUFF Material Description SRV-050-G12
  • STAUFF Material No. 1910000420
Diffuser Thread: 1" BSP
  • STAUFF Material Description SRV-114-G16
  • STAUFF Material No. 1910000421
  • STAUFF Material Description SRV-114-G16
  • STAUFF Material No. 1910000421
Diffuser Thread: 1 NPT
  • STAUFF Material Description SRV-114-N16
  • STAUFF Material No. 1910001835
  • STAUFF Material Description SRV-114-N16
  • STAUFF Material No. 1910001835
Diffuser Thread: 1 1/4" BSP
  • STAUFF Material Description SRV-200-G20
  • STAUFF Material No. 1910000422
  • STAUFF Material Description SRV-200-G20
  • STAUFF Material No. 1910000422
Diffuser Thread: 1-1/4 NPT
  • STAUFF Material Description SRV-200-N20
  • STAUFF Material No. 1910001408
  • STAUFF Material Description SRV-200-N20
  • STAUFF Material No. 1910001408
Diffuser Thread: 1 1/2" BSP
  • STAUFF Material Description SRV-227-G24
  • STAUFF Material No. 1910000423
  • STAUFF Material Description SRV-227-G24
  • STAUFF Material No. 1910000423
Diffuser Thread: 1-1/2 NPT
  • STAUFF Material Description SRV-227-N24
  • STAUFF Material No. 1910001407
  • STAUFF Material Description SRV-227-N24
  • STAUFF Material No. 1910001407
Diffuser Thread: 2" BSP
  • STAUFF Material Description SRV-454-G32
  • STAUFF Material No. 1910000424
  • STAUFF Material Description SRV-454-G32
  • STAUFF Material No. 1910000424
Diffuser Thread: 2 1/2" BSP
  • STAUFF Material Description SRV-650-G40
  • STAUFF Material No. 1910000425
  • STAUFF Material Description SRV-650-G40
  • STAUFF Material No. 1910000425
Diffuser Thread: 3" BSP
  • STAUFF Material Description SRV-950-G48
  • STAUFF Material No. 1910000426
  • STAUFF Material Description SRV-950-G48
  • STAUFF Material No. 1910000426

If you have a regular demand for pipework equipment and hydraulic components and you are looking for individual pricing for our product range, please contact STAUFF.

Purchases can be made using credit/debit cards. However, if you would like to register, please contact STAUFF before filling the shopping cart. Your registration request will then be reviewed within a very short time.

Slowing and settling return flow

Diffusers reduce fluid aeration, foaming and noise generated in hydraulic reservoirs

One of the basic prerequisites for the smooth operation of hydraulic systems is the selection of a well-designed hydraulic reservoir based on the specific requirements, which does not only supply the system with sufficient pressure fluid. It also uses suitable measures (e.g. filler breathers and sufficient tank pressurisation) to prevent solids, water and air from entering the system, contaminating the oil and affecting the function of sensitive components, which quite often results in expensive downtimes and unplanned oil changes.

Another factor that should not be underestimated is surface foaming which can form through uncontrolled return flow of hydraulic oil from the return line into the tank. As an air-in-oil dispersion, this can cause a number of operating problems throughout the system. These include efficiency losses for the energy used, operating malfunctions and a reduced service life of the oil. This can lead to marked oil loss due to oil excess foaming. Cavitation in the pump also increases noise generation in the system drastically, which in extreme cases can lead to a total breakdown and therefore to a system standstill.

This is where diffusers come into play: The design of the components is typically based on two concentric steel tubes where the perforated outlet sections are offset to each other, slowing down the oil in the return flow and settling it effectively. This can prevent the formation of oil foam and permanently reduce noise generated in hydraulic reservoirs. It also effectively prevents the raising of sedimentation and soil deposits from the bottom of smaller tanks. 

Diffusers are an ideal supplement to return-line filters with threaded outlets. They are connected directly to the return line or to the filter bowl of the filter housing. 

The diffusers are positioned fully underneath the minimum liquid level of the reservoir, ideally with the closed surface of the outer steel tube facing the suction end of the pump.

Main Characteristics of STAUFF Diffusers
  • Suitable for use with Mineral and Petroleum based hydraulic fluids (HL and HLP)  

  • Lengths between 109 and 272 mm 

  • Diameters between 64 and 150 mm 

  • Connection with female thread: 

  • 3/4" BSP to 3" BSP according to ISO 228 

  • 3/4" NPT to 3" NPT according to ANSI B1.20.1 

  • Alternative sizes and special designs available on request. 

  • Operating temperature range from -20 °C to +100 °C 

  • Maximum working pressure up to 20 bar in the return-line 

  • Threaded end cap made of Aluminium  

  • All other components made of Steel, zinc-plated 

WishlistEditArrow LeftArrow RightArrow Right ThinArrow Down DownloadMenuArrowCaret DownCloseResetVISAmatercardpaypalDHLInformationHermesCheckCheck-additionalStarAdd to Shopping Cartchevron-leftchevron-rightSpinnerHeartSyncGiftchevron-upKlarnaFiltersFileImagePdfWordTextExcelPowerpointArchiveCsvAudioVideoCalendarCart